Imported-Repos/UA3REO-DDC-Transceiver
1
0
Fork 0
mirror of https://github.com/XGudron/UA3REO-DDC-Transceiver.git synced 2025-08-07 16:50:33 +03:00
Code Issues Packages Projects Releases Wiki Activity

10.0.0 release

Browse Source
This commit is contained in:
Dmitry Panin
2024-07-02 00:06:39 +03:00
parent 821c30340e
commit e4d773e16e
3 changed files with 137 additions and 76 deletions
Download Patch File Download Diff File Expand all files Collapse all files

93
README.md
View File

@@ -250,9 +250,11 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **RF Power** - Transmission power,%
* **Repeater Mode"** - Operation mode via repeater
* **Repeater offset, kHz"** - Transmission frequency offset in repeater mode
* **SelfHear SSB** - Self-monitoring for SSB/AM modes, always active for DIGI/RTTY/LOOPBACK
* **SelfHear Volume** - Self Hearing (CW/DIGI) volume relative to the overall transceiver volume
* **TUNER Enabled** - Turning on the antenna tuner
* **Tune Type** - TUNE operating mode (carrier, two signal tone, multi-tone, white noise)
* **TOT, min** - Protection of the transmitter from long-term operation, automatic shutdown after time has elapsed
* **VOX Threshold, dbFS** - VOX Threshold, dbFS
* **VOX Timeout, ms** - VOX transmission delay after silence, milliseconds
* **VOX** - TX Voice activation
@@ -311,6 +313,7 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **FFT dBm Grid** - FFT signal power grid
* **LCD Brightness** - Set LCD brightness (not all lcd support)
* **LCD Sleep Timeout** - Idle time before the screen brightness decreases, sec (0 - disabled)
* **S-Meter style** - Selecting layout of the analog S-Meter
* **Show Sec VFO** - Show secondary VFO position on spectrum
* **WTF Color** - Waterfall colors: 1(blue -> yellow -> red), 2(black -> yellow -> red), 3(black -> yellow -> green), 4(black -> red), 5(black -> green), 6(black -> blue), 7(black -> white)
* **WTF Moving** - Mowe waterfall with frequency changing
@@ -354,20 +357,32 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
### Calibration [appears by long pressing the MENU button in the settings menu]
* **ALC Port Enabled** - Activation of transceiver power control by an external amplifier via the ALC line: up to 1 volt - ALC is disabled and the power set in the transceiver is used. from 1.0v to 3.0v - power adjustment from 0 to 100%
* **ALC Inverted** - Invert ALC logic (3.0v - 0%, 1.0v - 100%)
* **AM Modulation Index** - Set TX AM Modulation Scale
* **ATU Averaging** - The number of steps of averaging SWR values during measurements in the operation of an automatic tuner
* **BPF x** - Bandpass filter parameters
### Calibration Bands
* **ENABLE 2200m/60m/6m/4m/FM/2m/AIR/Marine Band/70cm** - Enable hidden bands
* **NOTX xxx** - Disable TX on selected bands
### Calibration Control
* **CAT Type** - Type of CAT subsystem (FT-450 / TS-2000)
* **COM CAT DTR/RTS** - Configuring the functions of the DTR/RTS control lines of the CAT port
* **SEC COM Mode** - Select the operating mode of the secondary COM port (debugging, CAT)
* **SEC COM DTR/RTS** - Configuring the functions of the DTR/RTS control lines of the Debug port
* **CICCOMP Shift** - Bit shift after CIC compensator
* **Calibrate reset** - Reset all calibrations to defaults
* **FAN Full start** - Temperature of the PA for starting the fan at full speed
* **FAN Medium start** - Temperature of the PA for starting the fan at medium speed
* **FAN Medium stop** - Temperature of the PA for stopping the fan
* **FAN Medium PWM** - Adjusting the duty cycle of a PWM fan in Medium mode
* **FAN Motherboard** - Starting the fan not only by the sensor, but also by the temperature of the STM32 processor
* **IF Gain MIN/MAX** - IF Gain adjusting limits
* **OTA Update** - Enable OTA firmware update over WiFi
### Calibration Hardware
* **RF-Unit Type** - RF-Unit Type (QRP / BIG)
* **ALC Port Enabled** - Activation of transceiver power control by an external amplifier via the ALC line: up to 1 volt - ALC is disabled and the power set in the transceiver is used. from 1.0v to 3.0v - power adjustment from 0 to 100%
* **ALC Inverted** - Invert ALC logic (3.0v - 0%, 1.0v - 100%)
* **BPF x** - Bandpass filter parameters
* **HPF START** - HPF filter parameters
* **LPF END** - LPF filter parameters
* **DAC Driver Mode** - DAC Driver OPA2673 bias mode (2 = 100% bias, 1 = 75% bias, 0 = 50% bias)
* **DAC Shift** - Bit shift of the output to the DAC
* **ENABLE 2200m/60m/6m/4m/FM/2m/AIR/Marine Band/70cm** - Enable hidden bands
* **DAC Interpolation** - Using interpolation in the first DAC frequency zone (HF)
* **EXT xxx** - External port control by band (EXT3, EXT2, EXT1, EXT0) - open drain
* **Encoder acceleration** - The encoder acceleration on faster rotation speeds
* **Encoder debounce** - Time of debouncing contacts of the main encoder
@@ -377,39 +392,14 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **Encoder2 debounce** - Time of debouncing contacts of the additional encoder
* **Encoder2 invert** - Invert the rotation of the additional encoder
* **Encoder2 on fall** - Mode of operation of the secondary encoder (some encoders skip a step or make an extra one)
* **FAN Full start** - Temperature of the PA for starting the fan at full speed
* **FAN Medium start** - Temperature of the PA for starting the fan at medium speed
* **FAN Medium stop** - Temperature of the PA for stopping the fan
* **FAN Medium PWM** - Adjusting the duty cycle of a PWM fan in Medium mode
* **FAN Motherboard** - Starting the fan not only by the sensor, but also by the temperature of the STM32 processor
* **FM Deviation Scale** - Set TX FM Deviation Scale
* **Flash GT911** - Starting the touchpad update procedure according to LCD screen resolution
* **HPF START** - HPF filter parameters
* **IF Gain MIN/MAX** - IF Gain adjusting limits
* **INA226** - Activation and calibration of the INA226 voltage/current sensor on the I2C bus
* **KTY81 Calibration** - Calibration of the KTY81 sensor (setting the resistance of the divider arm)
* **LCD Rotate** - Rotate screen at 180 degrees
* **LNA Compensation** - Compensates the S-meter value when the LNA is turned on, dBm
* **ATT Compensation** - Compensates the S-meter value when the ATT is turned on
* **LPF END** - LPF filter parameters
* **Linear Pwr Control** - Sets a linear way to change the signal amplitude when adjusting the power (if disabled - logarithmic)
* **MAX ChargePump, kHz** - Maximum PWM frequency for ChargePump circuit
* **MAX PWR on Meter** - Maximim RF power (for indication)
* **MAX Power in TUNE** - Maximum RF power in Tune mode
* **MAX RF Temp** - Maximum temperature of the PA before the protection operation
* **MAX SWR** - Maximum VSWR before protection operation
* **NOTX xxx** - Disable TX on selected bands
* **OTA Update** - Enable OTA firmware update over WiFi
* **RF GAIN xxx** - Calibration of the maximum TX output power for each range
* **RF-Unit Type** - RF-Unit Type (QRP / BIG)
* **RTC COARSE CALIBR** - Very coarse clock crystal calibration
* **RTC FINE CALIBR** - Clock crystal calibration, one division is 0.954 ppm
* **S METER** - S-meter calibration (LHF 160/80, MHF 40/30/20/17, HHF 15/12/10, 6M, VHF, SHF)
* **Sequencer support** - External sequencer support (output throught line EXT_TUNE)
* **SSB Power addition** - Addition of RF power in SSB power, %
* **SWR FWD/BWD RATE** - Adjustment of the transformation ratio of the SWR meter (forward / return)
* **Swap USB IQ** - Swap USB IQ output
* **Settings reset** - Reset all settings to defaults
* **TCXO Frequency, kHz** - Frequency adjustment of the reference oscillator
* **VCXO Correction** - Correction for main generator frequency offset
* **Touchpad flip** - Flip the touchpad operation horizontally/vertically
@@ -418,18 +408,47 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **Touchpad click timeout** - Maximum time for triggering a short click, ms
* **Touchpad hold timeout** - Time before a long press is triggered, ms
* **Touchpad swipe threshold** - Minimum distance to trigger a swipe, px
* **TSignal Balance** - Sets the power balance between signals in Two signal tune mode
* **TX CICCOMP Shift** - Bit shift after TX CIC compensator
* **TX Start Delay** - Delay before the RF signal is applied (ms), so that the relay has time to trigger
* **Tangent Type** - Select tangent type
* **Transverter Offset, MHz** - Offset frequency shown on the display (for custom transverters)
* **Transverter xxx IF, MHz** - Setting the IF frequency of the transverter
* **Transverter xxx RF, MHz** - Setting the RF frequency of the transceiver to match the IF
* **Transv only TX** - Use transverter only for TX
* **VHF Mixer Board** - Enable VHF board with RF mixer support (Wolf-2)
* **VHF Mixer IF, MHz** - Select IF frequency for VHF board mixer (Wolf-2)
* **VHF TCXO, kHz** - Select TCXO frequency for VHF board (Wolf-2)
* **VHF TCXO Correction** - Correction for VHF board TCXO generator frequency offset (Wolf-2)
### Calibration RX
* **ATT Compensation** - Compensates the S-meter value when the ATT is turned on
* **LNA Compensation** - Compensates the S-meter value when the LNA is turned on, dBm
* **CICCOMP Shift** - Bit shift after CIC compensator
* **S METER** - S-meter calibration (LHF 160/80, MHF 40/30/20/17, HHF 15/12/10, 6M, VHF, SHF)
* **Swap USB IQ** - Swap USB IQ output
### Calibration TX
* **AM Modulation Index** - Set TX AM Modulation Scale
* **ATU Averaging** - The number of steps of averaging SWR values during measurements in the operation of an automatic tuner
* **TX CICCOMP Shift** - Bit shift after TX CIC compensator
* **DAC Shift** - Bit shift of the output to the DAC
* **FM Deviation Scale** - Set TX FM Deviation Scale
* **Linear Pwr Control** - Sets a linear way to change the signal amplitude when adjusting the power (if disabled - logarithmic)
* **MAX PWR on Meter** - Maximim RF power (for indication)
* **MAX Power in TUNE** - Maximum RF power in Tune mode
* **MAX RF Temp** - Maximum temperature of the PA before the protection operation
* **MAX SWR** - Maximum VSWR before protection operation
* **Max Current, Amp** - Current protection, turns off transmission when the threshold is reached
* **RF GAIN xxx** - Calibration of the maximum TX output power for each range
* **SSB Power addition** - Addition of RF power in SSB power, %
* **SWR FWD/BWD RATE** - Adjustment of the transformation ratio of the SWR meter (forward / return)
* **SWR Protector** - SWR protection mode selection: Off, low power, transmission off
* **TSignal Balance** - Sets the power balance between signals in Two signal tune mode
* **TX Start Delay** - Delay before the RF signal is applied (ms), so that the relay has time to trigger
### Calibration Reset
* **Settings reset** - Reset all settings to defaults
* **Calibrate reset** - Reset all calibrations to defaults
* **WiFi Settings reset** - Reset all WiFi setings to defaults
### Memory Channels
* Changing names for transceiver memory channels