Imported-Repos/UA3REO-DDC-Transceiver
1
0
Fork 0
mirror of https://github.com/XGudron/UA3REO-DDC-Transceiver.git synced 2025-08-08 09:01:04 +03:00
Code Issues Packages Projects Releases Wiki Activity

13.0.0 Release

Browse Source
This commit is contained in:
UA3REO
2025-06-17 21:00:33 +03:00
parent f046ad890c
commit 1084908a62
3 changed files with 44 additions and 9 deletions
Download Patch File Download Diff File Expand all files Collapse all files

10
README.md
View File

@@ -106,6 +106,7 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **Beeper** - Beep on key press
* **Callsign** - Operator callsign
* **Operator Name** - Operator name
* **Locator** - User QTH locator
* **Channel Mode** - Channel frequency mode (for LPD/PMR and etc.)
* **Custom Transverter** - Enable external transverter on non-ham band (just offset display frequency)
* **Debug Type** - Output of debug and service information to USB / UART ports
@@ -117,7 +118,7 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **ENC2 Step Mult** - Frequency step multiplier for ENC2 rotation (for CW/SSB)
* **Notch Step** - Frequency step of manual notch filter
* **Full Duplex** - Full duplex RX+TX mode
* **Locator** - User QTH locator
* **Second COM Mode** - Select the operating mode of the secondary COM port (debugging, CAT, DATA)
* **SPLIT type** - In DX mode - the TX frequency is controlled, in the CrossBand mode synchronously for two VFOs, for Free only the RX frequency changes
* **RIT Interval** - Offset range RIT (+ -)
* **XIT Interval** - Offset range XIT (+ -)
@@ -209,7 +210,8 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **RF Power** - Transmission power, %
* **RF Power ENC3 step** - Power adjustment step by encoder (Wolf-2)
* **Repeater Mode"** - Operation mode via repeater
* **Repeater offset, kHz"** - Transmission frequency offset in repeater mode
* **Repeater offset, kHz** - Transmission frequency offset in repeater mode
* **Repeater tone** - Adds 1750Hz tone at the beginning of transmission to open the repeater (in FM mode)
* **SelfHear CW** - Self-control CW Gain
* **SelfHear on SSB** - Self-monitoring for SSB/AM modes, always active for DIGI/RTTY/LOOPBACK
* **SelfHear VOICE** - Self Hearing volume at voice modes relative to the overall transceiver volume
@@ -218,7 +220,7 @@ WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT co
* **TUNER Enbl per band** - Save tuner on/off state for each band independently
* **Tune Type** - TUNE operating mode (carrier, two signal tone, multi-tone, white noise)
* **TOT, min** - Protection of the transmitter from long-term operation, automatic shutdown after time has elapsed
* **VOX Threshold, dbFS** - VOX Threshold, dbFS
* **VOX Threshold, dBFS** - VOX Threshold, dBFS
* **VOX Timeout, ms** - VOX transmission delay after silence, milliseconds
* **VOX** - TX Voice activation
@@ -347,7 +349,6 @@ Allowed insertions in macros:
### Calibration Control
* **CAT Type** - Type of CAT subsystem (FT-450 / TS-2000)
* **COM CAT DTR/RTS** - Configuring the functions of the DTR/RTS control lines of the CAT port
* **SEC COM Mode** - Select the operating mode of the secondary COM port (debugging, CAT)
* **SEC COM DTR/RTS** - Configuring the functions of the DTR/RTS control lines of the Debug port
* **FAN Full start** - Temperature of the PA for starting the fan at full speed
* **FAN Medium start** - Temperature of the PA for starting the fan at medium speed
@@ -402,6 +403,7 @@ Allowed insertions in macros:
* **Transv only TX** - Use transverter only for TX
* **VHF Mixer Board** - Enable VHF board with RF mixer support (Wolf-2)
* **VHF Mixer IF, MHz** - Select IF frequency for VHF board mixer (Wolf-2)
* **VHF Mixer Current** - Selecting the mixer current level (Wolf-2)
* **VHF TCXO, kHz** - Select TCXO frequency for VHF board (Wolf-2)
* **VHF TCXO Correction** - Correction for VHF board TCXO generator frequency offset (Wolf-2)